Download Prospectus


How do we analyse the deflection of simply supported beams using calculus.

In our previous article on deflection in simply supported beams, we looked at calculating deflection using standard tables.  In this article, however, our focus will be on calculating deflection using calculus. 

Relationship Between Deflection, Slope and Radius of Curvature

As we mentioned in our previous articles, a beam bends when it’s subject to loading.  In the image below, you can see a simple beam before being loaded, then the same beam after being loaded.

a diagram of a beam before and after loading

To derive an expression relating to the slope, deflection, and radius of curvature of a beam, let us consider a small portion (labelled AB) of a beam bent into an arc, shown the image below:

diagram of a beam bent into an arc

Let ds = Length of beam AB

C= = the center of the arc (into which the beam has been bent),

 = Angle which the tangent at A makes with XX – axis, and +d = Angle which the tangent at B makes with XX-axis

We then find, from the geometry of the figure, that:

geometry of the arc

If the coordinates of point A are x and y, then:

tan calculation of the arc

Differentiating the above equation with respect to x, we obtain

, How do we analyse the deflection of simply supported beams using calculus.

From bending theory of a beam, the expression relating the radius of curvature, moment of inertia, elastic modulus and moment is given by:

, How do we analyse the deflection of simply supported beams using calculus.

Now, if we substitute 1R=d2ydx2 into the above equation, we will have 

, How do we analyse the deflection of simply supported beams using calculus.

Units in the above equation include:

E = elastic modulus in N/m2

I = moment of inertia in m4

M = moment in Nm

y and x are taken in m.

This equation is the fundamental expression from which the slope and deflection in a beam can be calculated. Slope and deflection expressions can be obtained by carrying out double integration and applying boundary conditions of the beam to solve the expressions.

Sign Conventions

To find out the slope and deflection of a centre line of a beam at any point proper, there is need to use sign conventions. The following sign conventions will be used:

  1.  x is positive when measured towards the right.
  2. y is negative when measured downwards.
  3.  M (bending moment) is negative when hogging.
  4.  Slope is negative when the rotation is clockwise.

Double integration Method

As we’ve seen, the fundamental equation for obtaining slope and deflection in beam is

double integration calculation

Note that first integration of the above equation gives the value of slope (dydx).  The second integration of the expression gives the value of the deflection (y).

Simply supported beam of span l carrying a point load at mid span.

Let‘s consider a simply supported beam AB of span l carrying a point load W at mid-span C, shown in Fig 19. Since the load is symmetrically applied, the maximum deflection (ymax) will occur at mid span.

diagram at mid span

The support reactions at A and B equals = W2

Consider the left half AC of the span. The bending moment at any section XX in AC distance. x from A is given by,

, How do we analyse the deflection of simply supported beams using calculus.

First integration gives,

, How do we analyse the deflection of simply supported beams using calculus.

Where C1 is the constant of integration.

Applying boundary conditions: at 

, How do we analyse the deflection of simply supported beams using calculus.

Thus we have,

, How do we analyse the deflection of simply supported beams using calculus.

Substituting the value of C1 gives 

, How do we analyse the deflection of simply supported beams using calculus.

Slope (dydx) at the support A, i.e when x = 0

Therefore, 

, How do we analyse the deflection of simply supported beams using calculus.

Integrating the slope equation once more, gives

, How do we analyse the deflection of simply supported beams using calculus.

and again using the boundary conditions:

, How do we analyse the deflection of simply supported beams using calculus.

Hence, we have

deflection equations

which is the deflection equation.  Substitute  x = l2 to obtain the mid-span deflection

mid span deflection

Hence, deflection at C, equals 

deflection at C

Example of a 4m span beam

A simply supported beam with a 4 m span carries a uniformly distributed load of 20 kN/m on the whole span. Calculate the maximum slope and deflection of the beam. Take E = 2 105 N/mm2 and I = 5000 104 mm4.

Length of beam = 4 m

UDL = 20 kN/m = 20000 N/m

E = 2 105 N/mm2 = 2 1011 N/m2 

I = 5000 104 mm4 = 0.00005 m2

Slope is given by wl324EI = 20000 4324 2 1011 0.00005 = 5.3310-3 rad

Maximum deflection (occurring at midspan) is given by ymax= 5wl4384EI = 520000443842 1011 0.00005 = 0.00667 m

Keep an eye out for future articles on more engineering calculations, tips and explanations.

Interested in our courses?

Interested in civil or mechanical engineering? Find out more about all the civil engineering courses we have available by clicking here, and the mechanical engineering courses by clicking here.

Diploma in Civil Engineering

Diploma in Mechanical Technology

Diploma in Mechanical Engineering

Diploma in Renewable Energy

Diploma in Material Science

Diploma in Sustainable Construction

Diploma in Structural Engineering

Diploma in Thermodynamics

Diploma in Building and Construction Engineering

Diploma in Thermofluids

Higher International Certificate in Civil Engineering

Higher International Diploma in Civil Engineering 

Higher International Diploma in Mechanical Engineering

Higher International Certificate in Mechanical Engineering

Alternatively, you can view all our online engineering courses here.

Recent Posts

Kirchhoff’s current and voltage laws

Kirchhoff’s current and voltage laws In our last article, we looked at the principles and operation of a d.c motor.  In this article, we’re going to investigate Kirchoff’s current and voltage laws, as well as how to apply them to engineering problems. Kirchoff’s law of  current Kirchoff’s law of current states that the algebraic sum […]

What are the principles of operation of a DC electric motor?

What are the principles of operation of a DC electric motor? In our last article, we looked at the electrical parameters in series and parallel electrical circuits.  In this article, we’re going to dive into the principles of operation of a DC electric motor. The motor effect When a current-carrying conductor is placed on a […]

What are the electrical parameters in series and parallel electrical networks?

What are the electrical parameters in series and parallel electrical networks? In our last article, we looked at the principles of operation of electrical cells.  In this article we’re going to move on to the electrical parameters in both series and parallel electrical networks. When we have circuits with more than one resistor, we need […]